Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.0-00261
S - IMAGE_VARIANT_STRING=HAAAANAAA
S - OEM_IMAGE_VERSION_STRING=C-BPATTH
S - Boot Config, 0x000002e3
S - Core 0 Frequency, 0 MHz
B -      1548 - PBL, Start
B -      3497 - bootable_media_detect_entry, Start
B -    206841 - bootable_media_detect_success, Start
B -    206845 - elf_loader_entry, Start
B -    208788 - auth_hash_seg_entry, Start
B -    209001 - auth_hash_seg_exit, Start
B -    236968 - elf_segs_hash_verify_entry, Start
B -    297350 - PBL, End
B -    245830 - SBL1, Start
B -    296795 - pm_device_init, Start
D -     14274 - pm_device_init, Delta
B -    311557 - boot_flash_init, Start
D -        30 - boot_flash_init, Delta
B -    315583 - boot_config_data_table_init, Start
D -    439444 - boot_config_data_table_init, Delta - (0 Bytes)
B -    759572 - CDT version:3,Platform ID:24,Major ID:1,Minor ID:0,Subtype:0
B -    765794 - sbl1_ddr_set_params, Start
B -    769484 - cpr_init, Start
D -         0 - cpr_init, Delta
B -    775096 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    787601 - pm_driver_init, Start
D -      6832 - pm_driver_init, Delta
B -    803156 - clock_init, Start
D -        30 - clock_init, Delta
B -    813313 - Image Load, Start
D -     32452 - QSEE Image Loaded, Delta - (460664 Bytes)
B -    845795 - Image Load, Start
D -       640 - SEC Image Loaded, Delta - (2048 Bytes)
B -    852993 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    860801 - Image Load, Start
D -     14884 - QHEE Image Loaded, Delta - (51952 Bytes)
B -    875685 - Image Load, Start
D -     16409 - RPM Image Loaded, Delta - (149492 Bytes)
B -    892125 - Image Load, Start
D -     22661 - APPSBL Image Loaded, Delta - (479072 Bytes)
B -    914786 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    920490 - SBL1, End
D -    677008 - SBL1, Delta
S - Flash Throughput, 56000 KB/s  (1143228 Bytes,  20374 us)
S - DDR Frequency, 400 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk

[10] platform_init()
[10] target_init()
[20] initialising mmc_slot =2
[20] Error: Command timeout error
[20] Failure getting OCR response from MMC Card
[30] MMC card failed to respond, try for SD card
[90] Done initialization of the card
[90] pm8x41_get_is_cold_boot: cold boot
[100] Not able to search the panel:
[100] Display not enabled for 24 HW type
[100] Target panel init not found!
[110] pm8x41_get_is_cold_boot: cold boot
[110] partition misc doesn't exist
[110] error in emmc_recovery_init
[120] Unable to locate /bootselect partition
[120] No 'misc' partition found
[120] Error reading MISC partition
[130] failed to get ffbm cookie[130] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[140] Loading boot image (413696): start
[160] Loading boot image (413696): done
[170] DTB Total entry: 15, DTB version: 2
[170] Using DTB entry 0x000000f7/00000000/0x00010018/0 for device 0x000000f7/00010000/0x00010018/0
[180] Using pmic info 0x2000b/0x0/0x0/0x0 for device 0x2000b/0x0/0x0/0x0
[180] cmdline:  androidboot.emmc=true androidboot.serialno=79d93d1d androidboot.baseband=apq mdss_mdp.panel=0:dsi:0:
[190] Updating device tree: start
[240] Updating device tree: done
[390] Error: Command timeout error
[390] card sleep error: mmc_put_card_to_sleep
[390] booting linux @ 0x80080000, ramdisk @ 0x82000000 (0), tags/device tree @ 0x81e00000
[400] Jumping to kernel via monitor


U-Boot 2016.01-rc1 (Dec 08 2015 - 11:39:05 +0000)
Qualcomm-DragonBoard 410C

DRAM:  986 MiB
MMC:   msm_sdhci: 0, msm_sdhci: 1
reading uboot.env
In:    serial
Out:   serial
Err:   serial
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0
ENVCMD
reading dragonboard-kernel_9.snap/kernel.img
22508032 bytes read in 6136 ms (3.5 MiB/s)
reading dragonboard-kernel_9.snap/dtbs/apq8016-sbc.dtb
66447 bytes read in 40 ms (1.6 MiB/s)
reading dragonboard-kernel_9.snap/initrd.img
5363894 bytes read in 1474 ms (3.5 MiB/s)
## Flattened Device Tree blob at 83000000
   Booting using the fdt blob at 0x83000000
   Using Device Tree in place at 0000000083000000, end 000000008301338e

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-1024-snapdragon (buildd@bos01-arm64-002) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.2) ) #27-Ubuntu SMP Fri Aug
12 11:45:29 UTC 2016 (Ubuntu 4.4.0-1024.27-snapdragon 4.4.16)
[    0.000000] Boot CPU: AArch64 Processor [410fd030]
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0x00000000b9000000
[    0.000000] PERCPU: Embedded 17 pages/cpu @ffffffc03d941000 s31256 r8192 d30184 u69632
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM errata 826319, 827319, 824069
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 224784
[    0.000000] Kernel command line:  androidboot.emmc=true androidboot.serialno=79d93d1d androidboot.baseband=apq mdss_mdp.panel=0:dsi:0: console=ttyMSM0,115200n8 root=
/dev/disk/by-label/writable net.ifnames=0 init=/lib/systemd/systemd ro panic=-1 fixrtc snap_core=ubuntu-core_639.snap snap_kernel=dragonboard-kernel_9.snap
[    0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] log_buf_len min size: 16384 bytes
[    0.000000] log_buf_len: 32768 bytes
[    0.000000] early log buf free: 14508(88%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0xb4600000-0xb8600000] (64MB) mapped at [ffffffc034600000-ffffffc0385fffff]
[    0.000000] Memory: 735012K/913408K available (12924K kernel code, 1708K rwdata, 6044K rodata, 1196K init, 844K bss, 112860K reserved, 65536K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0000000 - 0xffffffbdc0f68000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc03da00000   (   986 MB)
[    0.000000]       .init : 0xffffffc001308000 - 0xffffffc001433000   (  1196 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc001308000   ( 18976 KB)
[    0.000000]       .data : 0xffffffc00144c000 - 0xffffffc0015f7200   (  1709 KB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000]
[    0.000000] **********************************************************
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **                                                      **
[    0.000000] ** trace_printk() being used. Allocating extra memory.  **
[    0.000000] **                                                      **
[    0.000000] ** This means that this is a DEBUG kernel and it is     **
[    0.000000] ** unsafe for production use.                           **
[    0.000000] **                                                      **
[    0.000000] ** If you see this message and you are not debugging    **
[    0.000000] ** the kernel, report this immediately to your vendor!  **
[    0.000000] **                                                      **
[    0.000000] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000] **********************************************************
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000670] Console: colour dummy device 80x25
[    0.000698] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.000709] pid_max: default: 32768 minimum: 301
[    0.000797] Security Framework initialized
[    0.000805] Yama: becoming mindful.
[    0.000866] AppArmor: AppArmor initialized
[    0.001024] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.001034] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.001647] Initializing cgroup subsys io
[    0.001663] Initializing cgroup subsys memory
[    0.001688] Initializing cgroup subsys devices
[    0.001700] Initializing cgroup subsys freezer
[    0.001712] Initializing cgroup subsys net_cls
[    0.001722] Initializing cgroup subsys perf_event
[    0.001733] Initializing cgroup subsys net_prio
[    0.001744] Initializing cgroup subsys hugetlb
[    0.001756] Initializing cgroup subsys pids
[    0.001799] ftrace: allocating 43450 entries in 170 pages
[    0.103366] EFI services will not be available.
[    0.103393] ASID allocator initialised with 65536 entries
[    0.110598] Detected VIPT I-cache on CPU1
[    0.110647] CPU1: Booted secondary processor [410fd030]
[    0.111717] Detected VIPT I-cache on CPU2
[    0.111757] CPU2: Booted secondary processor [410fd030]
[    0.112759] Detected VIPT I-cache on CPU3
[    0.112795] CPU3: Booted secondary processor [410fd030]
[    0.112862] Brought up 4 CPUs
[    0.112888] SMP: Total of 4 processors activated.
[    0.112899] CPU: All CPU(s) started at EL1
[    0.112926] alternatives: patching kernel code
[    0.113640] devtmpfs: initialized
[    0.131103] evm: security.selinux
[    0.131114] evm: security.SMACK64
[    0.131135] evm: security.SMACK64EXEC
[    0.131141] evm: security.SMACK64TRANSMUTE
[    0.131146] evm: security.SMACK64MMAP
[    0.131151] evm: security.ima
[    0.131156] evm: security.capability
[    0.131786] DMI not present or invalid.
[    0.132091] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.134895] pinctrl core: initialized pinctrl subsystem
[    0.136543] NET: Registered protocol family 16
[    0.147214] cpuidle: using governor ladder
[    0.159222] cpuidle: using governor menu
[    0.159739] vdso: 2 pages (1 code @ ffffffc001451000, 1 data @ ffffffc001450000)
[    0.159770] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.162648] DMA: preallocated 256 KiB pool for atomic allocations
[    0.162979] Serial: AMBA PL011 UART driver
[    0.182304] irq: no irq domain found for /soc/q6-smp2p/slave-kernel !
[    0.182861] irq: no irq domain found for /soc/wcnss-smp2p/slave-kernel !
[    0.186973] irq: no irq domain found for /soc/qcom,mdss_mdp@1a00000 !
[    0.188162] qcom-smd smd: new channel 'rpm_requests' info-size: 88 fifo-size: 1024
[    0.213542] ACPI: Interpreter disabled.
[    0.222851] msm_bus_fabric_init_driver
[    0.223056] msm_bus_device 580000.ad-hoc-bus: Dev 1024
[    0.223075] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[    0.223085] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[    0.223215] msm_bus_device 580000.ad-hoc-bus: Dev 0
[    0.223230] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[    0.223239] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[    0.223363] msm_bus_device 580000.ad-hoc-bus: Dev 4096
[    0.223379] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[    0.223389] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[    0.229374] msm_bus_init_clk: Valid node clk node 1024 ctx 0
[    0.229381] msm_bus_init_clk: Valid node clk node 1024 ctx 1msm_bus_init_clk: Valid node clk node 0 ctx 0
[    0.229469] msm_bus_init_clk: Valid node clk node 0 ctx 1msm_bus_init_clk: Valid node clk node 4096 ctx 0
[    0.229560] msm_bus_init_clk: Valid node clk node 4096 ctx 1[    0.362448] vgaarb: loaded
[    0.389569] SCSI subsystem initialized
[    0.400254] usbcore: registered new interface driver usbfs
[    0.401280] usbcore: registered new interface driver hub
[    0.402601] usbcore: registered new device driver usb
[    0.408291] media: Linux media interface: v0.10
[    0.408998] Linux video capture interface: v2.00
[    0.416062] dmi: Firmware registration failed.
[    0.423339] Advanced Linux Sound Architecture Driver Initialized.
[    0.436038] Bluetooth: Core ver 2.21
[    0.436569] NET: Registered protocol family 31
[    0.436585] Bluetooth: HCI device and connection manager initialized
[    0.436777] Bluetooth: HCI socket layer initialized
[    0.436914] Bluetooth: L2CAP socket layer initialized
[    0.437226] Bluetooth: SCO socket layer initialized
[    0.445832] NetLabel: Initializing
[    0.445859] NetLabel:  domain hash size = 128
[    0.445870] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.446630] NetLabel:  unlabeled traffic allowed by default
[    0.454386] clocksource: Switched to clocksource arch_sys_counter
[    1.257042] AppArmor: AppArmor Filesystem Enabled
[    1.268749] pnp: PnP ACPI: disabled
[    1.415079] NET: Registered protocol family 2
[    1.429609] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    1.431778] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[    1.439404] TCP: Hash tables configured (established 8192 bind 8192)
[    1.445750] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    1.446372] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    1.451589] NET: Registered protocol family 1
[    1.460519] RPC: Registered named UNIX socket transport module.
[    1.460568] RPC: Registered udp transport module.
[    1.460591] RPC: Registered tcp transport module.
[    1.460603] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.464610] Trying to unpack rootfs image as initramfs...
[   10.574596] Freeing initrd memory: 5236K (ffffffc004000000 - ffffffc00451d000)
[   10.584653] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[   10.589287] kvm [1]: HYP mode not available
[   10.623815] futex hash table entries: 1024 (order: 5, 131072 bytes)
[   10.628786] audit: initializing netlink subsys (disabled)
[   10.631282] audit: type=2000 audit(10.551:1): initialized
[   10.641722] Initialise system trusted keyring
[   10.649800] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[   10.820526] zbud: loaded
[   10.837790] VFS: Disk quotas dquot_6.6.0
[   10.841443] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[   10.874939] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   10.913727] NFS: Registering the id_resolver key type
[   10.914501] Key type id_resolver registered
[   10.914525] Key type id_legacy registered
[   10.914733] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   10.918434] fuse init (API version 7.23)
[   10.928413] 9p: Installing v9fs 9p2000 file system support
[   10.939362] Key type big_key registered
[   10.969345] Key type asymmetric registered
[   10.969497] Asymmetric key parser 'x509' registered
[   10.975922] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[   10.978064] io scheduler noop registered
[   10.978095] io scheduler deadline registered
[   10.982002] io scheduler cfq registered (default)
[   11.025419] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   11.026005] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[   11.082768] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[   11.214402] msm_serial 78af000.serial: msm_serial: detected port #1
[   11.217452] msm_serial 78af000.serial: uartclk = 3686400
[   11.218888] 78af000.serial: ttyMSM1 at MMIO 0x78af000 (irq = 130, base_baud = 230400) is a MSM
[   11.225194] msm_serial 78b0000.serial: msm_serial: detected port #0
[   11.226110] msm_serial 78b0000.serial: uartclk = 3686400
[   11.226898] 78b0000.serial: ttyMSM0 at MMIO 0x78b0000 (irq = 131, base_baud = 230400) is a MSM
[   11.227091] msm_serial: console setup on port #0
[   12.344550] console [ttyMSM0] enabled
[   12.355015] msm_serial: driver initialized
[   12.366795] [drm] Initialized drm 1.1.0 20060810
[   12.373144] l6: supplied by s4
[   12.408226] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[   12.411268] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[   12.417258] l2: supplied by s3
[   12.426111] msm_dsi_manager_register: failed to register mipi dsi host for DSI 0
[   12.428220] msm 1a00000.qcom,mdss_mdp: failed to bind 1a98000.qcom,mdss_dsi (ops dsi_ops): -517
[   12.439242] msm 1a00000.qcom,mdss_mdp: master bind failed: -517
[   12.934470] brd: module loaded
[   13.075264] loop: module loaded
[   13.136296] spi_qup 78b7000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[   13.162367] spi_qup 78b9000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[   13.178503] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[   13.307032] libphy: Fixed MDIO Bus: probed
[   13.307411] tun: Universal TUN/TAP device driver, 1.6
[   13.310316] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.328624] sky2: driver version 1.30
[   13.332700] PPP generic driver version 2.4.2
[   13.337643] usbcore: registered new interface driver asix
[   13.339499] usbcore: registered new interface driver ax88179_178a
[   13.343270] usbcore: registered new interface driver cdc_ether
[   13.348894] usbcore: registered new interface driver dm9601
[   13.354579] usbcore: registered new interface driver net1080
[   13.359984] usbcore: registered new interface driver plusb
[   13.365888] usbcore: registered new interface driver cdc_subset
[   13.371180] usbcore: registered new interface driver zaurus
[   13.377794] usbcore: registered new interface driver cdc_ncm
[   13.407423] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   13.407698] ehci-pci: EHCI PCI platform driver
[   13.413961] ehci-platform: EHCI generic platform driver
[   13.418823] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[   13.425338] msm_hsusb_host 78d9000.ehci: unable to find transceiver
[   13.429123] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   13.434453] ohci-pci: OHCI PCI platform driver
[   13.441522] ohci-platform: OHCI generic platform driver
[   13.446113] uhci_hcd: USB Universal Host Controller Interface driver
[   13.453412] usbcore: registered new interface driver cdc_acm
[   13.456744] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   13.463381] usbcore: registered new interface driver usblp
[   13.470703] usbcore: registered new interface driver cdc_wdm
[   13.476227] usbcore: registered new interface driver uas
[   13.482371] usbcore: registered new interface driver usb-storage
[   13.488950] usbcore: registered new interface driver usbserial
[   13.493321] usbcore: registered new interface driver usbserial_generic
[   13.499053] usbserial: USB Serial support registered for generic
[   13.518936] usb3503 usb2513: switched to HUB mode
[   13.519039] usb3503 usb2513: usb3503_probe: probed in hub mode
[   13.530747] usbip_core: USB/IP Core v1.0.0
[   13.531631] usbcore: registered new device driver usbip-host
[   13.533974] usbip_host: USB/IP Host Driver v1.0.0
[   13.547374] mousedev: PS/2 mouse device common for all mice
[   13.566418] input: pm8941_pwrkey as /devices/platform/soc/200f000.spmi/spmi-0/0-00/200f000.spmi:pm8916@0:pwrkey@800/input/input0
[   13.576393] i2c /dev entries driver
[   13.582334] i2c_qup 78b6000.i2c:
[   13.582334]  tx channel not available
[   13.594851] i2c_qup 78b8000.i2c:
[   13.594851]  tx channel not available
[   13.642902] i2c_qup 78ba000.i2c:
[   13.642902]  tx channel not available
[   13.669600] l3: supplied by s3
[   13.673739] CPR closed loop is enabled
[   13.679238] CPR is enabled!
[   13.704959] qcom-tsens 4a8000.thermal-sensor: tsens calibration failed
[   13.711386] device-mapper: uevent: version 1.0.3
[   13.719387] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[   13.719595] Bluetooth: HCI UART driver ver 2.3
[   13.727063] Bluetooth: HCI UART protocol H4 registered
[   13.731242] Bluetooth: HCI UART protocol BCSP registered
[   13.736369] Bluetooth: HCI UART protocol LL registered
[   13.741829] Bluetooth: HCI UART protocol ATH3K registered
[   13.746787] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   13.753556] Bluetooth: HCI UART protocol Intel registered
[   13.759099] Bluetooth: HCI UART protocol BCM registered
[   13.763894] Bluetooth: HCI UART protocol QCA registered
[   13.770341] usbcore: registered new interface driver btusb
[   13.782430] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[   13.801804] sdhci: Secure Digital Host Controller Interface driver
[   13.801921] sdhci: Copyright(c) Pierre Ossman
[   13.807721] Synopsys Designware Multimedia Card Interface Driver
[   13.813575] sdhci-pltfm: SDHCI platform and OF driver helper
[   13.852556] l5: supplied by s4
[   13.854105] sdhci_msm 7824900.sdhci: Failed getting OCR mask: 0
[   13.902451] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[   13.908912] sdhci_msm 7864900.sdhci: Got CD GPIO
[   13.973054] mmc0: MAN_BKOPS_EN bit is not set
[   13.978566] mmc0: new high speed MMC card at address 0001
[   13.990946] mmcblk0: mmc0:0001 DS2008 7.28 GiB
[   13.995750] mmcblk0boot0: mmc0:0001 DS2008 partition 1 4.00 MiB
[   14.000325] mmcblk0boot1: mmc0:0001 DS2008 partition 2 4.00 MiB
[   14.003899] mmcblk0rpmb: mmc0:0001 DS2008 partition 3 4.00 MiB
[   14.016163] mmc1: Reset 0x1 never completed.
[   14.034043] Alternate GPT is invalid, using primary GPT.
[   14.034890]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29
[   14.052281] sdhci_msm 7864900.sdhci: No vmmc regulator found
[   14.156163] mmc1: Reset 0x1 never completed.
[   14.205528] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using ADMA 64-bit
[   14.254421] ledtrig-cpu: registered to indicate activity on CPUs
[   14.262604] hidraw: raw HID events driver (C) Jiri Kosina
[   14.265244] mmc1: new high speed SDHC card at address aaaa
[   14.275816] usbcore: registered new interface driver usbhid
[   14.275915] usbhid: USB HID core driver
[   14.285605] mmcblk1: mmc1:aaaa SE32G 29.7 GiB
[   14.288675] qcom-q6v5-pil 4080000.qcom,mss: invalid resource
[   14.292904] DEBUG:pil: starting vdd
[   14.294921] DEBUG:pil: done vdd
[   14.308725] l7: supplied by s4
[   14.321267]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9
[   14.329517] qcom-q6v5-pil 4080000.qcom,mss: Found relocation area 75497472@0x0000000086800000
[   14.332632]  remoteproc0: 4080000.qcom,mss is available
[   14.337427]  remoteproc0: Note: remoteproc is still under development and considered experimental.
[   14.342275]  remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[   14.354638]  remoteproc0: Direct firmware load for mba.mbn failed with error -2
[   14.362288]  remoteproc0: failed to load 4080000.qcom,mss
[   14.387500] qcom-tz-pil soc:pronto_rproc: Found relocation area 6291456@0x000000008b600000
[   14.388794]  remoteproc1: soc:pronto_rproc is available
[   14.394813]  remoteproc1: Note: remoteproc is still under development and considered experimental.
[   14.399945]  remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[   14.410924]  remoteproc1: Direct firmware load for wcnss.mdt failed with error -2
[   14.412445] qcom-tz-pil soc:vidc_tzpil@0: no crash reason id
[   14.415260] soc:vidc_tzpil@0 supply qcom,pll not found, using dummy regulator
[   14.415872] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uV, skipping
[   14.415899] qcom-tz-pil soc:vidc_tzpil@0: failed to read qcom,pll_uA, skipping
[   14.415923] qcom-tz-pil soc:vidc_tzpil@0: no wdog IRQ defined
[   14.415949] qcom-tz-pil soc:vidc_tzpil@0: no fatal IRQ defined
[   14.415955] qcom-tz-pil soc:vidc_tzpil@0: no ready IRQ defined
[   14.415966] qcom-tz-pil soc:vidc_tzpil@0: no handover IRQ defined
[   14.415982] qcom-tz-pil soc:vidc_tzpil@0: no stop-ack IRQ defined
[   14.416380] qcom-tz-pil soc:vidc_tzpil@0: Found relocation area 8388608@0x000000008f800000
[   14.417452]  remoteproc2: soc:vidc_tzpil@0 is available
[   14.417467]  remoteproc2: Note: remoteproc is still under development and considered experimental.
[   14.417481]  remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[   14.418800]  remoteproc2: Direct firmware load for venus.mdt failed with error -2
[   14.418877]  remoteproc2: failed to load soc:vidc_tzpil@0
[   14.451852] coresight-tmc 825000.etf: TMC initialized
[   14.529220]  remoteproc1: failed to load soc:pronto_rproc
[   14.631779] coresight-tmc 826000.etr: TMC initialized
[   14.642375] coresight-tpiu 820000.tpiu: TPIU initialized
[   14.651094] coresight-funnel 821000.funnel: FUNNEL initialized
[   14.657758] coresight-funnel 841000.funnel: FUNNEL initialized
[   14.674594] coresight-etm4x 85c000.etm: ETM 4.0 initialized
[   14.684774] coresight-etm4x 85d000.etm: ETM 4.0 initialized
[   14.694657] coresight-etm4x 85e000.etm: ETM 4.0 initialized
[   14.704152] coresight-etm4x 85f000.etm: ETM 4.0 initialized
[   14.710479] coresight-replicator-qcom 824000.replicator: REPLICATOR 1.0 initialized
[   14.726919] usbcore: registered new interface driver snd-usb-audio
[   14.765078] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[   14.765414] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[   14.775049] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[   14.785544] apq8016-lpass-cpu 7708000.lpass-cpu: asoc_qcom_lpass_cpu_platform_probe() error getting mi2s-osr-clk: -2
[   14.811813] l5: Restricting voltage, 2700000-1800000uV
[   14.813846] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: msm8x16_wcd_codec_probe :PMIC REV: 1
[   14.816130] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: msm8x16_wcd_codec_probe :CODEC Version: 1
[   14.834617] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: ASoC: no source widget found for VDD_SPKDRV
[   14.834786] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: ASoC: Failed to add route VDD_SPKDRV -> direct -> SPK DAC
[   14.866506] qcom-apq8016-sbc 7702000.sound: msm8x16_wcd_i2s_rx1 <-> Primary MI2S mapping ok
[   14.877428] qcom-apq8016-sbc 7702000.sound: adv7511 <-> Quatenary MI2S mapping ok
[   14.883180] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: ASoC: mux RX2 MIX1 INP3 has no paths
[   14.884289] msm8x16-wcd-codec 200f000.spmi:pm8916@1:codec@f000: ASoC: mux RX3 MIX1 INP3 has no paths
[   14.958422] NET: Registered protocol family 10
[   14.974309] sit: IPv6 over IPv4 tunneling driver
[   14.986585] NET: Registered protocol family 17
[   14.989139] Bluetooth: RFCOMM TTY layer initialized
[   14.990245] Bluetooth: RFCOMM socket layer initialized
[   14.996227] Bluetooth: RFCOMM ver 1.11
[   15.000440] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   15.003944] Bluetooth: HIDP socket layer initialized
[   15.011442] 9pnet: Installing 9P2000 support
[   15.016470] Key type dns_resolver registered
[   15.032484] registered taskstats version 1
[   15.032951] Loading compiled-in X.509 certificates
[   15.041083] Loaded X.509 cert 'Build time autogenerated kernel key: 2fa34e65f542786574a0fe11ea34af238c2eec9d'
[   15.043036] zswap: loaded using pool lzo/zbud
[   15.156876] Key type trusted registered
[   15.338031] Key type encrypted registered
[   15.339118] AppArmor: AppArmor sha1 policy hashing enabled
[   15.341503] ima: No TPM chip found, activating TPM-bypass!
[   15.349662] evm: HMAC attrs: 0x1
[   15.362887] msm_iommu 1f00000.qcom,iommu: invalid resource
[   15.365587] msm_iommu 1f00000.qcom,iommu: iface: 100000000, core: 800000000
[   15.367714] msm_iommu 1f00000.qcom,iommu: device gfx_iommu (model: 500) mapped at ffffff80017a0000, with 2 ctx banks
[   15.374866] msm_iommu 1f00000.qcom,iommu: iommu sec: pgtable size: 94208
[   15.412161] genirq: Setting trigger mode 1 for irq 156 failed (gic_set_type+0x0/0x68)
[   15.412834] msm_iommu 1f00000.qcom,iommu: Request Global CFG IRQ 156 failed with ret=-22
[   15.430809] msm_iommu_ctx 1f09000.qcom,iommu-ctx: context gfx3d_user using bank 1
[   15.439628] msm_iommu_ctx 1f0a000.qcom,iommu-ctx: context gfx3d_priv using bank 2
[   15.443954] msm_iommu 1e00000.qcom,iommu: iface: 100000000, core: 800000000
[   15.446954] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8001b80000, with 20 ctx banks
[   15.454333] genirq: Setting trigger mode 1 for irq 156 failed (gic_set_type+0x0/0x68)
[   15.463957] msm_iommu 1e00000.qcom,iommu: Request Global CFG IRQ 156 failed with ret=-22
[   15.478017] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context jpeg_enc0 using bank 2
[   15.483760] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context vfe using bank 3
[   15.490769] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context mdp_0 using bank 4
[   15.497559] msm_iommu_ctx 1e25000.venus_ns: context venus_ns using bank 5
[   15.504167] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context cpp using bank 6
[   15.510605] msm_iommu_ctx 1e27000.qcom,iommu-ctx: context mDSP using bank 7
[   15.517509] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context gss using bank 8
[   15.523958] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context a2 using bank 9
[   15.531222] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context mdp_1 using bank 18
[   15.537603] msm_iommu_ctx 1e33000.venus_sec_pixel: context venus_sec_pixel using bank 19
[   15.544995] msm_iommu_ctx 1e34000.venus_sec_bitstream: context venus_sec_bitstream using bank 20
[   15.553111] msm_iommu_ctx 1e35000.venus_sec_non_pixel: context venus_sec_non_pixel using bank 21
[   15.561799] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_fw using bank 22
[   15.570760] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context periph_rpm using bank 23
[   15.578004] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context periph_CE using bank 24
[   15.585349] msm_iommu_ctx 1e39000.qcom,iommu-ctx: context periph_BLSP using bank 25
[   15.592924] msm_iommu_ctx 1e3a000.qcom,iommu-ctx: context periph_SDC1 using bank 26
[   15.600552] msm_iommu_ctx 1e3b000.qcom,iommu-ctx: context periph_SDC2 using bank 27
[   15.608080] msm_iommu_ctx 1e3c000.qcom,iommu-ctx: context periph_audio using bank 28
[   15.615729] msm_iommu_ctx 1e3d000.qcom,iommu-ctx: context periph_USB_HS1 using bank 29
[   15.651439] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[   15.655102] 1a98000.qcom,mdss_dsi supply gdsc not found, using dummy regulator
[   15.666896] msm 1a00000.qcom,mdss_mdp: bound 1a98000.qcom,mdss_dsi (ops dsi_ops)
[   15.667383] msm 1a00000.qcom,mdss_mdp: bound 1c00000.qcom,adreno-3xx (ops a3xx_ops)
[   15.675082] 1a00000.qcom,mdss_mdp supply vdd not found, using dummy regulator
[   15.717581] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   15.717719] [drm] No driver support for vblank timestamp query.
[   15.728375] msm 1a00000.qcom,mdss_mdp: No connectors reported connected with modes
[   15.729191] [drm] Cannot find any crtc or sizes - going 1024x768
[   16.006416] Console: switching to colour frame buffer device 128x48
[   16.129296] msm 1a00000.qcom,mdss_mdp: fb0: msm frame buffer device
[   16.146788] [drm] Initialized msm 1.0.0 20130625 on minor 0
[   16.163261] msm_otg 78d9000.phy: OTG regs = ffffff800179c000
[   16.167305] msm_otg 78d9000.phy: no vddcx
[   16.283472] msm_hsusb_host 78d9000.ehci: EHCI Host Controller
[   16.283657] msm_hsusb_host 78d9000.ehci: new USB bus registered, assigned bus number 1
[   16.288847] msm_hsusb_host 78d9000.ehci: irq 142, io mem 0x078d9000
[   16.301855] input: gpio_keys as /devices/platform/gpio_keys/input/input1
[   16.302383] hctosys: unable to open rtc device (rtc0)
[   16.306184] msm_hsusb_host 78d9000.ehci: USB 2.0 started, EHCI 1.00
[   16.306322] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   16.306327] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   16.306330] usb usb1: Product: EHCI Host Controller
[   16.306334] usb usb1: Manufacturer: Linux 4.4.0-1024-snapdragon ehci_hcd
[   16.306337] usb usb1: SerialNumber: 78d9000.ehci
[   16.306739] hub 1-0:1.0: USB hub found
[   16.306760] hub 1-0:1.0: 1 port detected
[   16.360165] ALSA device list[   16.363407] Freeing unused kernel memory: 1196K (ffffffc001308000 - ffffffc001433000)
[   16.363462] Freeing alternatives memory: 72K (ffffffc001433000 - ffffffc001445000)
Loading, please wait...
starting version 229
[   16.403288] random: systemd-udevd urandom read with 9 bits of entropy available
[   16.618225] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[   16.750677] usb 1-1: New USB device found, idVendor=0424, idProduct=2513
[   16.750703] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   16.757207] hub 1-1:1.0: USB hub found
[   16.763705] hub 1-1:1.0: 3 ports detected
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done.
Begin: Running /scripts/nfs-premount ... done.
Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... ext4
hwclock: can't open '/dev/misc/rtc': No such file or directory
done.
[   17.468375] initrd: checking filesystem for writable partition
[   17.473978] EXT4-fs (mmcblk1p9): couldn't mount as ext3 due to feature incompatibilities
[   17.501765] EXT4-fs (mmcblk1p9): recovery complete
[   17.502702] EXT4-fs (mmcblk1p9): mounted filesystem with ordered data mode. Opts: errors=remount-ro
ext4
[   17.562830] EXT4-fs (mmcblk1p9): couldn't mount as ext3 due to feature incompatibilities
[   17.572350] EXT4-fs (mmcblk1p9): mounted filesystem with ordered data mode. Opts: (null)
[   17.700290] initrd: mounting /run
mkdir: can't create directory '/root/writable/system-data//etc/hosts': File exists
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/nfs-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[   18.717822] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4
+SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[   18.718140] systemd[1]: Detected architecture arm64.

Welcome to Ubuntu 16.04.1 LTS!

[   18.764131] systemd[1]: No hostname configured.
[   18.764166] systemd[1]: Set hostname to <localhost>.
[   19.103379] systemd[1]: writable.mount: Unit is bound to inactive unit dev-mmcblk1p9.device. Stopping, too.\FD[  OK  ] Listening on udev Kernel Socket.
[   1\FD[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[   1}\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Listening on fsck to fsckd communication Socket.
[   1\FD[  OK  ] Created slice User and Session Slice.
[   1\FD\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Started Dispatch Password Requests to Console Directory Watch.
[   1\FD\FD+L\FD&\FD[H\FDj
                \A3\FD0m] Listening on Journal Socket (/dev/log).
[   \00\FD+L\FD&\FD[H\FDj
               \A3\FD0m] Reached target Remote File Systems (Pre).
[   1\F5\FD\9A\FDj\FDz\FD   i\FD\FD\FD\FD*kW\FD+\FD\FD\FD\FD
                              \FDU\FD.[\FD\AA
\FD\FD8\FD[   1}\FD\FD+\FD\FD&\FD[H\FDj
                                                           \A3\FD0m] Listening on Journal Audit Socket.
[   \00\FD+L\FD&\FD[H\FDj
               \A3+\FDm] Listening on /dev/initctl Compatibility Named Pipe.
[   1\FD[  OK  ] Set up automount Arbitrary Executab...ats File System Automount Point.
[   1}\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Reached target Swap.
[   1\FD\FD+L\FD&\FD[H\FDj
                \A3\FD0m] Listening on udev Control Socket.
[   1[  OK  ] Reached target Encrypted Volumes.
[   1}\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Listening on Journal Socket.
[   1\FD\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Reached target Remote File Systems.
[   1}\FD\FD+L\FD&\FD[H\FDj
                 \A3+\FDm] Created slice System Slice.
[   19.318324\FD         Mounting Huge Pages File System...
[   19.332146] systemd[1]: Starting Nameserver information manager...
         Starting Nameserver information manager...
[   19.348767] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   19.366868] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[  OK  ] Created slice system-systemd\x2dfsck.slice.
[   19.386046] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[   19.416053] systemd[1]: Starting Set the host\FD         Starting Set the hostname to the va...red on the writable partition...
[   19.438841] systemd[1]: Starting Create list of required static device nodes for the current kernel...
         Starting Create list of required st... nodes for the current kernel...
[   19.466843] systemd[1]: \FD[  OK  ] Created slice system-serial\x2dgetty.slice.
[   19.481623] systemd[1]: Starting Load Kernel Modules...
         Starting Load Kernel Modules...
[   19.521350] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[   19.5[  OK  ] Created slice system-getty.slice.
[   19.566381] syste\FD         Mounting Debug File System...
[   19.578351] system[  OK  ] Reached target Slices.
[   19.6\FD[  OK  ] Mounted Debug File System.
[   1\FD[  OK  ] Mounted POSIX Message Queue File System.
[   1\FD[  OK  ] Mounted Huge Pages File System.
[   19\FD[  OK  ] Started Journal Service.
[  OK  ] Started Remount Root and Kernel File Systems.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for Trigger resolvconf update for networkd DNS.
[DEPEND] Dependency failed for D-Bus System Message Bus.
[DEPEND] Dependency failed for Timer to automatically refresh installed snaps.
[DEPEND] Dependency failed for Cgroup management proxy.
[DEPEND] Dependency failed for Network Service Bus Name.
[DEPEND] Dependency failed for Login Service.
[DEPEND] Dependency failed for System Logging Service.
[DEPEND] Dependency failed for Serial Getty on ttyMSM0.
[DEPEND] Dependency failed for Getty on tty1.
[DEPEND] Dependency failed for getty on tty2...us and logind are not available.
[DEPEND] Dependency failed for Ubuntu FAN network setup.
[DEPEND] Dependency failed for Snappy daemon.
[DEPEND] Dependency failed for LSB: Set the ... Scaling governor to "ondemand".
[DEPEND] Dependency failed for Restore /etc/...fore the ppp link was shut down.
[DEPEND] Dependency failed for Daily Cleanup of Temporary Directories.
[DEPEND] Dependency failed for D-Bus System Message Bus Socket.
[DEPEND] Dependency failed for Cgroup management daemon.
[DEPEND] Dependency failed for Basic System.
[DEPEND] Dependency failed for Multi-User System.
[DEPEND] Dependency failed for Graphical Interface.
[DEPEND] Dependency failed for OpenBSD Secure Shell server.
[DEPEND] Dependency failed for Socket activation for snappy daemon.
[DEPEND] Dependency failed for Regular background program processing daemon.
[DEPEND] Dependency failed for Generate sshd host keys.
[DEPEND] Dependency failed for Notify bootloader that boot was successful.
[DEPEND] Dependency failed for Permit User Sessions.
[DEPEND] Dependency failed for /etc/rc.local Compatibility.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Nameserver information manager.
         Starting Set the hostname to the va...red on the writable partition...
         Starting Apply Kernel Variables...
         Starting Create Static Device Nodes in /dev...
         Mounting FUSE Control File System...
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Login Prompts.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Paths.
         Starting udev Coldplug all Devices...
[  OK  ] Mounted FUSE Control File System.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting Set the hostname to the va...red on the writable partition...
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /var/lib/sudo...
         Mounting /tmp...
         Mounting /mnt...
         Starting udev Kernel Device Manager...
[  OK  ] Mounted /tmp.
[  OK  ] Mounted /mnt.
[  OK  ] Mounted /var/lib/sudo.
[  OK  ] Started udev Coldplug all Devices.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Started udev Kernel Device Manager.
         Starting Set the hostname to the va...red on the writable partition...
         Starting Network Service...
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[   21.214250]  remoteproc2: powering up soc:vidc_tzpil@0
[  OK  ] Started Network Service.
[   21.257612]  remoteproc2: Booting fw image venus.mdt, size 6812
[  OK  ] Reached target Sound Card.
         Starting Set the hostname to the va...red on the writable partition...
[   21.403975] rtc-pm8xxx 200f000.spmi:pm8916@0:rtc@6000: rtc core: registered pm8xxx_rtc as rtc0

See 'systemctl status snappy-set-hostname.service' for details.
[   21.457737] \FD[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[   21.537204] qcom-tz-pil soc:vidc_tzpil@0: start successful
[   21.\FD[  OK  ] Found device /dev/ttyMSM0.
[   21.613194] cfg80211: World regulatory domain updated:
[   21.613218] cfg80211:  DFS Master region: unset
[   21.617262] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   21.621826] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   21.631395] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   21.639204] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   21.647190] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   21.655179] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   21.664911] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   21.674372] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   21.682433] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   21.767157] iris_read_\FD[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Found device /dev/mmcblk1p8.
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
         Mounting /var/lib/cloud...
         Mounting /var/lib/initramfs-tools...
         Mounting /var/lib/dhcp...
         Mounting /var/cache/apparmor...
[   21.970293]  remoteproc1: powering up soc:pronto_rproc
[   21.9890\FD         Mounting /var/lib/apparmor...
         Mounting /snap...
         Starting File System Check on /dev/mmcblk1p8...
         Mounting /var/lib/misc...
         Mounting /var/lib/systemd/random-seed...
         Mounting /var/lib/dbus...
         Mounting /var/lib/logrotate...
         Mounting /var/tmp...
         Mounting /var/snap...
         Mounting /home...
         Mounting /var/lib/extrausers...
         Mounting /var/lib/waagent...
         Mounting /var/lib/console-conf...
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
         Mounting /var/lib/snapd...
         Mounting /var/log...
         Mounting /var/lib/systemd/rfkill...
         Mounting /root...
[  OK  ] Mounted /home.
[  OK  ] Mounted /snap.
[  OK  ] Mounted /var/snap.
[  OK  ] Mounted /var/lib/cloud.
[  OK  ] Mounted /var/lib/dbus.
[  OK  ] Mounted /var/lib/dhcp.
[  OK  ] Mounted /var/lib/logrotate.
[  OK  ] Mounted /var/log.
[  OK  ] Mounted /var/cache/apparmor.
[  OK  ] Mounted /var/lib/apparmor.
[  OK  ] Mounted /var/tmp.
[  OK  ] Mounted /var/lib/initramfs-tools.
[  OK  ] Mounted /var/lib/misc.
[  OK  ] Mounted /var/lib/waagent.
[  OK  ] Mounted /root.
[  OK  ] Mounted /var/lib/extrausers.
[  OK  ] Mounted /var/lib/snapd.
[  OK  ] Mounted /var/lib/systemd/random-seed.
[  OK  ] Mounted /var/lib/systemd/rfkill.
[  OK  ] Mounted /var/lib/console-conf.
[  OK  ] Started File System Check on /dev/mmcblk1p8.
[   22.701514] qcom-smd smd: new channel 'IPCRTR' info-size: 40 fifo-size: 8192
[   22.737352] qcom-smd smd: new channel 'sys_mon' info-size: 40 fifo-size: 1024
[   22.749755] qcom-smd smd: new channel 'APPS_RIVA_CTRL' info-size: 40 fifo-size: 8192
[   22.749819] qcom-smd smd: new channel 'APPS_RIVA_DATA' info-size: 40 fifo-size: 8192
[   22.833183] qcom-tz-pil soc:pronto_rproc: start successful
[   22.833206]  remoteproc1: remote processor soc:pronto_rproc is now up
[  OK  ] Started File System Check Daemon to report status.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[   22.954647] qcom-smd smd: new channel 'WCNSS_CTRL' info-size: 40 fifo-size: 8192
[   22.954697] qcom-smd smd: new channel 'WLAN_CTRL' info-size: 40 fifo-size: 8192
[   22.961319] qcom_smd_wlan_ctrl_probe: enter
         Mounting /boot/uboot...
         Starting Load/Save Random Seed...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Mounted /boot/uboot.
[   23.142263] systemd-journald[1120]: Received request t\FD[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Reached target Local File Systems.
         Starting Run snappy firstboot setup...
         Starting LSB: AppArmor initialization...
[  OK  ] Started Flush Journal to Persistent Storage.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Create Volatile Files and Directories.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
         Starting Update UTMP about System Boot/Shutdown...
         Starting Network Time Synchronization...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
         Starting Update UTMP about System Runlevel Changes...
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Started Update UTMP about System Runlevel Changes.
[  OK  ] Started Network Time Synchronization.
[   23.884382] audit: type=1400 audit(1474289357.447:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=1380 com
m="apparmor_parser"

[   23.901464] audit: type=1400 audit(1474289357.463:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.ac
tion" pid=1379 comm="apparmor_parser"
[   23.901522] audit: type=1400 audit(1474289357.463:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" p
id=1379 comm="apparmor_parser"
[   23.918408] audit: type=1400 audit(1474289357.483:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script"
 pid=1379 comm="apparmor_parser"
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started LSB: AppArmor initialization.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
         Starting Raise network interfaces...
[FAILED] Failed to start Run snappy firstboot setup.
See 'systemctl status snapd.firstboot.service' for details.
[   24.200862] fw_status: 2
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
[   24.250776] qcom-smd smd: new channel 'APPS_RIVA_BT_CMD' info-size: 40 fifo-size: 8192
[   24.250829] qcom-smd smd: new channel 'APPS_RIVA_BT_ACL' info-size: 40 fifo\FDSee 'systemctl status snappy-set-hostname.service' for detai[   24.265622] qcom-smd smd:
new channel 'APPS_RIVA_ANT_DATA' info-size: 40 fifo-size: 2048
ls.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[FAILED] Failed to start Raise network interfaces.
See 'systemctl status networking.service' for details.
[  OK  ] Reached target Bluetooth.
[  OK  ] Reached target Network.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
         Starting Load/Save RF Kill Switch Status...
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[DEPEND] Dependency failed for System Initialization.
[DEPEND] Dependency failed for System Logging Service.
[  OK  ] Reached target System Initialization.
         Starting System Logging Service...
[FAILED] Failed to start Set the hostname to...tored on the writable partition.
See 'systemctl status snappy-set-hostname.service' for details.
[  OK  ] Started System Logging Service.
[   27.327226] wcnss: received WCNSS_CBC_COMPLETE_IND from FW
[   27.327941] wcn36xx-msm a000000.qcom,wcn36xx: wcn36xx_msm_probe initialized
[   27.347035] wcn36xx: mac address: 02:00:79:d9:3d:1d
[  OK  ] Started Load/Save RF Kill Switch Status.